References
~~~~~~~~~~

.. [Oñate_1995] Oñate Ibáñez de Navarra, E. Cálculo de estructuras por el método de elementos finitos: análisis estático lineal. Barcelona: CIMNE, 1995.
.. [Malvern_1969] Malvern, L. E. Introduction to the mechanics of a continuous medium. Englewood Cliffs, N.J: Prentice-Hall, 1969.
.. [Hopkins_2005] Hopkins, P. Benchmarks for Membrane and bending analysis of Laminated Shells. Part 1. Stiffness matrix and thermal characteristics. NAFEMS, 2005.
.. [Hopkins_2005b] Hopkins, P. Benchmarks for Membrane and bending analysis of Laminated Shells. Part 2. Strength analysis. NAFEMS, 2005.
.. [Barbero_2018] Barbero, E. J. Introduction to composite materials design, Third edition. Boca Raton: CRC Press, Taylor & Francis Group, CRC Press is an imprint of the Taylor & Francis Group an informa business, 2018.
.. [NR546] Bureau Veritas. NR546 - Hull in composite, plywood and high density polyethylene materials. Bureau Veritas Rule Notes, November 2022.
.. [Rastellini_2007] F. Rastellini, S. Oller, O. Salomón, and E. Oñate, “Composite materials non-linear modelling for long fibre-reinforced laminates,” Comput. Struct., vol. 86, no. 9, pp. 879–896, May 2008, doi: 10.1016/j.compstruc.2007.04.009.
.. [Martínez_2008] Xavier Martínez, “Micro mechanical simulation of composite materials using the serial/parallel mixing theory,” Structural analysis, Universitat Politècnica de Catalunya, Barcelona, 2008.
.. [Simo_1987] J. C. Simo and J. W. Ju, “Strain- and stress-based continuum damage models—I. Formulation,” Int. J. Solids Struct., vol. 23, no. 7, pp. 821–840, 1987, doi: 10.1016/0020-7683(87)90083-7.
.. [Chaves_2003] E. W. V. Chaves and X. Oliver, A three dimensional setting for strong discontinuities modelling in failure mechanics, 1. ed. Barcelona: International Center for Numerical Methods in Engineering, 2003.
.. [Chaves_2013] E. W. V. Chaves and J. Oliver, “Notes on continuum damage models,” 2013.
.. [Oliver_1990] J. Oliver, S. Oller, and M. Cervera, “Isotropic damage models and smeared crack analysis of concrete,” Jan. 1990.
.. [Crisfield_2003]	M. A. Crisfield, Non-linear finite element analysis of solids and structures. Essentials, Reprinted., vol. 1. Chichester: Wiley, 2003.
.. [Simo_1998] J. C. Simo and T. J. R. Hughes, Computational inelasticity. New York: Springer, 1998.
.. [Bathe_2014]	K.-J. Bathe, Finite element procedures. S.l.: s.n., 2014.
.. [Crisfield_2991]	M. A. Crisfield, Non-linear finite element analysis of solids and structures. Advanced topics., vol. 2. Chichester ; New York: Wiley, 1991.
.. [Ortigosa_2011] Ortigosa, I. Development of a decision support system for the design and adjustment of sailboat rigging. PhD Thesis, Universitat Politècnica de Catalunya, 2011.
.. [Gutiérrez_2014] Gutiérrez, J.E. Desarrollo de herramientas software para el análisis de aerogeneradores offshore sometidos a cargas acopladas de viento y oleaje. PhD Thesis, Universidad Politécnica de Cartagena, 2014.
.. [Jurado_2021] Jurado-Granados, J. Desarrollo e implementación de una formulación utilizando la teoría de mezclas serie/paralelo para la modelización de estructuras navales de materiales compuestos sometidas bajo cargas cíclicas. PhD Thesis, Universidad Politécnica de Catalunya, 2021.
.. [Compassis_2015] Compass IS SA, 2015, SeaFEM Theory Manual, 2015
.. [API_2002] API RP 2A-WSD. American Petroleum Institute, Recommended Practice for Planning, Designing and Constructing Fixed Offshore PlatformsWorking Stress Design, 2002.
.. [Det_Norske_2005] Det Norske Veritas. Fatigue Design of Offshore Steel Structures. Recommended Practice DVN-RP-C203, 2005.
.. [Lloyds_Register_2009] Lloyds Register. Fatigue Design Assessment. Level 3 Procedure: Guidance on direct calculations, 2009.
.. [Tom_Irvine_2011] Tom Irvine. Rainflow Cycle Counting Method in Fatigue Analysis. 2011